1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
|
# Definition of mirror hosts we push.
# One mirror per line, with the following fields defined.
#
# Type ShortName HostName User SSHProtocol SSHKeyFile
#
# ALTERNATIVELY the line may look like
#
# Type ShortName HostName User -$SOMESSHOPTION
#
# The fields Type, ShortName, HostName and User are *mandantory*.
#
# Type is either all, staged or mhop, meaning:
# all - do a "normal" push. Trigger them, go on.
# This is the default for a Debian mirror. It does all the
# right things (when the mirror uses ftpsync), like staged-syncing.
# staged - do a two-stage push, waiting for them after stage 2(and all others that
# are staged) before doing stage2.
# Contrary to all, this waits for ALL downstream mirrors
# marked "staged", so most useful if they are behind a DNS RR
# and need to update dists/ at near the same time.
# mhop - send a multi-hop staged push. This will tell the mirror to initiate
# a mhop/stage1 push to its staged/mhop mirrors and then exit.
# When all mhop got back we then send the stage2 through to them.
#
# ShortName will be used as a shorthand in logfile outputs and for the logfile
# where every ssh output gets redirected to.
#
# If no SSHKeyFile is given, the default from the config file applies.
# If SSHProtocol is empty, it will default to 2, but if you want to
# define a keyfile you HAVE TO set protocol too!
#
# With the ALTERNATIVE syntax you are able to use any special ssh option
# you want just for one special mirror. The option after the username
# then MUST start with a -, in which case the whole rest of the line is taken
# as a set of options to give to ssh, it is passed through without doing
# anything with it.
#
# There is one caveat here: Should you want to use the -i option to give
# another ssh key to use, keep in mind that the master keyfile will
# always be presented too! That is, ssh will show both keys to the other
# side and the first one presented wins. Which might not be the key you
# want. There is currently no way around this, as that would mean
# dropping backward compatibility.
#
# Backwards compatibility:
# An older runmirrors script will NOT run with a newer runmirrors.mirror file, but
# a new runmirrors can run with an old runmirrors.mirror file. This should make updates
# painless.
#
# Examples:
# all eu.puccini puccini.debian.org archvsync 2
#
# -> will push puccini.debian.org, user archvsync, using ssh protocol 2
# and the globally configured ssh key.
#
# all eu.puccini puccini.debian.org archvsync -p 2222
#
# -> will do the same as above, but use port 2222 to connect to.
#
# staged eu.puccini puccini.debian.org archvsync
# staged eu.powell powell.debian.org archvsync
#
# -> will push both puccini and powell in stage1, waiting for both to
# finish stage1 before stage2 gets pushed. The username will be archvsync.
#
# staged eu.puccini puccini.debian.org archvsync
# mhop eu.powell powell.debian.org archvsync
#
# -> will do the same as above, but powell gets told about mhop and can then
# push its own staged/mhop mirrors before returning. When both returned
# then stage2 is sent to both.
#
# One special value is allowed: DELAY
# This word has to be on a line itself, followed by a space and a number.
# nothing else, not even whitespace. It will trigger a pause of $number
# seconds between the two mirrors. If no number is given it defaults to
# 600 seconds.
|
